0002 1.05 0 3.0 10000 900 N HV scan 0003 1.05 0 3.0 10000 880 N HV scan 0004 1.05 0 3.0 10000 860 N HV scan 0005 1.05 0 3.0 10000 840 N HV scan 0006 1.05 0 3.0 10000 820 N HV scan 0007 1.05 0 3.0 10000 800 N HV scan 0008 1.05 0 3.0 10000 780 N HV scan 0009 1.05 0 3.0 10000 760 N HV scan 0010 1.05 0 3.0 10000 740 N HV scan 0011 1.05 0 3.0 10000 720 N HV scan 0012 1.05 0 3.0 10000 700 N HV scan 0013 1.05 0 3.0 10000 860 Random HV scan 0014 1.05 0 3.0 10000 900 Random 0015 Junk 0 3.0 0016 1.05 0 3.0 50000 900 N 0017 1.05 0 3.0 10000 900 Random 0018 1.05 0 3.0 50000 900 N 0019 1.05 0 3.0 24588 900 N ion source switching (stop) 0020 1.05 0 3.0 50000 900 N 0021 1.05 0 3.0 12502 900 N reboot,trigger signals changed ? 0022 1.05 0 3.0 34487 900 N stop due to ACC beam test meeting 0023 1.05 0 3.0 10000 900 N after control cable replacement 0028 1.05 0 3.0 10000 900 N test after Samo cleaned the code 0029 1.05 0 3.0 10000 900 +P1 Ring, angle, OK 0030 1.05 0 3.0 2000 900 +P2 -||- 0031 1.05 0 3.0 10081 900 +P1+P2 during run opened beam more 0032 1.05 0 3.0 10000 900 tle same as prev. 0033 1.05 0 3.0 10000 900 tle same as prev. 0034 1.05 0 3.0 50000 900 N OK 0035 1.05 0 3.0 13096 900 N OK 0036 1.029 0 3.0 ? 900 N new aerog.-same distance, a. shutdown of prog.,recov. 0037 1.029 0 3.0 ? 900 N autoshutd..., recovered hbook 0038 1.029 0 3.0 ? 900 N distance changed:20 to 27 cm autoshutdown... 0039 1.029 0 3.0 9400 900 N OK 0040 1.029 0 3.0 50000 900 N OK, problems with beam (magnet) 0041 1.07 0 3.0 50000 900 N new aerogel, distance ch. to 16.4cm 0042 1.07 0 3.0 50000 900 N OK, beam down 0043 1.07 0 3.0 17707 900 N OK 0044 2x1.05 0 3.0 50000 900 N Two aerogels installed 0045 2x1.05 0 3.0 7481 900 N OK 0046 2x1.029 0 3.0 50000 900 N OK 0047 2x1.029 0 3.0 ? 900 N OK \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ The Dead channel was shiftted and the ring was covered Momentum scan start (1.029) , mapfile = bt_2_1_2.map \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0048 1.029 0 3.0 50000 900 N 0049 1.029 0 2.0 30000 900 N Momentum scan 0050 1.029 0 1.5 900 N Momentum scan 0051 1.029 0 1.0 15000 900 N Gate width 15mm 15mm 0052 1.029 0 0.8 15000 900 N MWPC damaged? 0053 1.029 0 0.8 1000 900 N Momentum scan 0054 1.029 0 0.8 1000 900 N Momentum scan 0055 1.029 0 0.8 1000 900 N Momentum scan 0056 1.029 0 / 2000 900 A1 MWPC test during Samo's access 0057 1.029 0 / 2000 / A1 MWPC test, V1=1.292V, V2=1.257V 0058 1.029 0 / 2000 / A2 MWPC test, V1=1.292V, V2=1.257V 0059 1.029 0 / 2000 / A1 MWPC test 0060 1.029 0 / 2000 / A1 TDC N17 replaced, ch.11(0=31) dead 0061 1.029 0 / 2000 / A2 MWPC test V1=1.292V, V2=1.293 0062 1.029 0 0.8 ? 900 N V1=1.292V, V2=1.293 0063 1.029 0 10070 900 N 0064 1.029 0 1.0 10000 900 N 0065 1.029 0 3.0 10000 900 N Polarity + 0066 1.029 0 0.5 10000 900 N Polarity - again 0067 1.029 0 10000 same \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Momentum scan end (1.029) , mapfile = bt_1_2_3.map Samo recovered The dead space. The full channel was read out!! \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0068 1.029 0 3.0 10000 900 N 0069 1.029 0 3.0 35016 900 N 0070 1.029 0 3.0 10000 900 N V1=1.401V, V2=1.398V 0071 1.029 0 3.0 10000 900 N MWPC V1=1.439V, V2=1.441V, modules rearranged 0072 Junk 0 3.0 0073 1.029 0 3.0 10000 900 N 0074 1.029 0 3.0 41122 900 N HDD full 0075 1.05 0 3.0 50000 900 N wrong DAQ exec 0076 1.05 0 3.0 5000 900 N wrong DAQ exec \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Momentum scan start (1.05) \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0077 1.05 0 3.0 900 N OK 0078 1.05 0 3.0 50000 900 N OK 0079 1.05 0 2.0 30000 900 N 0080 1.05 0 2.0 10000 900 N 0081 1.05 0 1.5 20610 900 N 0082 1.05 0 1.0 18933 900 N 0083 1.05 0 0.8 20000 900 N 0084 1.05 0 0.8 3211 900 N same 0085 1.05 0 0.5 20000 900 N \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Momentum scan end (1.05) \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0086 1.05 0 3.0 2000 900 N module changed, NIMM crate changed, test run 0087 1.05 0 3.0 8719 900 N 0088 1.05 0 3.0 30097 900 N 0089 1.05 0 3.0 45000 900 N 0090 1.05 0 3.0 50000 900 N 0091 1.029 0 3.0 50000 900 N reference run 0092 1.029 0 3.0 5000 900 N reference run \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Lens on !! angle scan start, mapfile = btl_1_2_3.map \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0093 1.029 0-Lens 3.0 25000 900 N LENSES! Distance 27.0 cm 0094 1.029 0-Lens 3.0 5000 900 N Distance 27.0 cm 0095 1.029 0-Lens 3.0 30000 900 N Distance ch. to 19.5 cm 0096 1.029 30-Lens 3.0 30000 900 N Distance ch. to 19.5 cm 0097 1.029 15-Lens 3.0 30000 900 N Distance ch. to 19.5 cm 0098 1.05 0-Lens 3.0 30000 900 N Twist cable was disconnected 0099 1.05 0-Lens 3.0 3000 900 N recover! Distance changed to 200mm 0100 1.05 0-Lens 3.0 30000 900 N Distance changed to 200mm 0101 1.05 0-Lens 3.0 28498 900 N Distance changed to 135mm 0102 1.05 30-Lens 3.0 900 N Distance changed to 135mm 0103 1.05 15-Lens 3.0 23178 900 N Distance changed to 135mm \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Lens on !! angle scan end \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Lens off !! angle scan start \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0104 1.05 0 3.0 25005 900 N Distance changed to 135mm 0105 1.05 30 3.0 30000 900 N Distance changed to 135mm 0106 1.05 30 3.0 4023 900 N Distance changed to 135mm 0107 1.05 15 3.0 20000 900 N Distance changed to 135mm 0108 Junk 3.0 0109 1.029 0 3.0 20000 900 N HV for MWPC was readjusted, but not changed ? PC1=PC2=1.444 0110 1.029 0 3.0 8821 900 N HV back to PC1=1.444,PC2=1.425 0111 1.029 30 3.0 20000 900 N 0112 1.029 15 3.0 20000 900 N 0113 1.029 15 3.0 4727 900 N 0114 1.029 15 3.0 10000 900 N \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Lens off !! angle scan end RICH HV scan start for fine granularity \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0115 1.029 0 3.0 4473 900 N ?????????? 0116 1.029 0 3.0 5000 900 N HV scan 0117 1.029 0 3.0 5000 850 N HV scan 0118 1.029 0 3.0 5000 800 N HV scan 0119 1.029 0 3.0 5000 750 N HV scan 0120 1.029 0 3.0 5000 700 N HV scan 0121 1.029 0 3.0 5000 725 N HV scan 0122 1.029 0 3.0 5000 775 N HV scan 0123 1.029 0 3.0 5000 825 N HV scan 0124 1.029 0 3.0 5000 875 N HV scan 0125 1.029 0 3.0 5000 675 N HV scan 0126 1.029 0 3.0 5000 650 N HV scan 0127 1.029 0 3.0 5000 625 N HV scan 0128 1.029 0 3.0 5000 925 N HV scan \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ RICH HV scan start for fine granularity \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Fine granularity , mapfile = bt_3_3_3_4.5.map \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0129 1.029 0 3.0 20000 850 N Change to fine granularity. Only HV2 (850 V) connected, mapfile changed 0130 1.029 0 3.0 20000 850 N referenc run 0131 1.029 0 3.0 20000 850 N referenc run 0132 1.029 0 3.0 5047 850 N referenc run \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ angle scan start \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0133 1.029 0 3.0 20000 850 N Distance changed to 19.5cm 0134 1.029 0 3.0 85?? 850 N 0135 1.029 30 3.0 20000 850 N 0136 1.029 30 3.0 4314 850 N 0137 1.029 15 3.0 14132 850 N VME crate replaced due to trouble with voltage output 0138 1.029 15 3.0 20000 850 N First run with new VME crate, reference run 0139 1.029 15 3.0 18483 850 N 0140 1.05 0 3.0 50000 850 N Aerogel changed to 1.05 , distance changed to 20.0 cm 0141 1.05 0 3.0 7850 850 N 0142 1.05 0 3.0 20000 850 N Distance changed 13.5 cm 0143 1.05 0 3.0 5345 850 N 0144 1.05 30 3.0 30000 850 N angle scan 0145 1.05 15 3.0 30000 850 N angle scan 0146 1.05 15 3.0 12339 850 N \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ angle scan end k/pi separation start \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0147 1.05 0 0.8 30000 850 N Distance to 20.0cm beam slit 10.0 mm(left,right) 0148 junk 0149 1.05 0 1.1 30000 850 N 0150 1.05 0 4.0 14707 850 N 14:44 beam stop 0151 1.05 0 4.0 20000 850 N 0152 1.05 0 4.0 12216 850 N 0153 1.05 0 3.0 10149 850 N Polarity + 0154 1.029 0 3.0 20000 850 N Distance to 27.0 cm 0155 1.029 0 4.0 20000 850 N beam slit 7.5mm (left,right) , D1 1300 0156 1.029 0 4.0 20000 850 N 0157 1.029 0 4.0 3368 850 N 17:58 beam down, 18:03 beam recovered 0158 1.029 0 1.1 20000 850 N beam slit 10mm (left, rigth) 0159 1.029 0 1.1 5694 850 N 0160 1.029 0 0.8 25041 850 N 0161 1.029 0 3.0 8120 850 N Polarity + , earth quake hoppened 0162 1.029 0 3.0 11096 850 N \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ k/pi separation end \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Option run \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0163 1.05 0 3.0 30000 850 N beam slit 5mm, sumiyoshi-san's gel 0164 1.029 0 3.0 7800 850 N Distance to 20.0 cm, cluck check 0165 1.029 0 3.0 30000 850 N Distance to 27.0 cm, cluck check 0166 1.029 0 3.0 20000 850 N Distance to 27.0 cm, cluck check \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ Lens on !! \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0167 1.05 0-Lens 3.0 30000 850 N 0168 1.029 0-Lens 3.0 30000 850 N \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ 0169 1.029 0-Lens 3.0 10000 850 random